Found a Crushed Dryer Vent or Foil Accordion Duct Mid-Job? What Operators Should Do
When you find a crushed dryer vent or foil accordion duct mid-job, stop and photograph it before touching anything. Then offer the customer a rigid or semi-rigid metal replacement as a written option. Clean the duct only if it can be cleaned without tearing it. If it can't, decline that section in writing and explain why.
Picture a routine cleaning, say in the typical $100–$160 range. You pull the dryer out and find foil flex duct squashed to the thickness of a paperback, with lint packed into every fold. The visit has turned into three jobs at once. You need to protect yourself, protect the customer, and keep the appointment from falling apart. The steps below cover how to handle non-code dryer venting from the first photo to the follow-up.
What should you do the moment you find crushed or foil accordion venting?
When you find crushed or foil accordion dryer venting, pause. Don't pull on the duct and don't push a brush into it. Foil flex duct tears easily, and a torn duct can dump lint into a wall cavity or crawlspace. A crushed section can also hide a blockage you can't see.
Work through these five steps in order:
- Power down. Unplug the dryer. On a gas dryer, leave the gas connection alone.
- Photograph the duct as found, before you move or clean anything.
- Check airflow at the termination. If it's safe, run the dryer briefly and see how much air comes out outside.
- Choose a path: clean, clean with limits, or refuse that section.
- Talk to the customer before you continue, not after.
How do you document non-code dryer venting so it protects you?
Document non-code dryer venting with timestamped photos taken before any work, plus a short written note on what you found and what you recommended. That record is your defense if the customer disputes your findings later or something goes wrong with the dryer.
Get these shots on every job:
- A wide shot of the dryer and the duct connection
- A close-up of the crushed, kinked, or foil section
- Any visible lint buildup or tears
- The exterior termination point
- A tape-measure shot if the run looks long or has many bends
Then write a note of two or three sentences covering the duct material, its condition, and what you advised. For example: "Found 6 ft of foil accordion duct, crushed behind dryer, heavy lint in folds. Recommended dryer duct replacement with rigid metal. Customer declined at this visit."
Before and after photo documentation that's attached to the job keeps this evidence with the work order instead of buried in your camera roll.
Why is foil accordion duct a problem for dryers?
Foil accordion duct causes problems for three reasons. Its ridged interior traps lint, it restricts airflow, and it crushes or tears easily. Many dryer manufacturers discourage it for the main exhaust run, and building codes in many jurisdictions prohibit it there.
The International Residential Code, published by the International Code Council, generally takes this approach:
- Main exhaust duct: metal with a smooth interior.
- Maximum developed length: typically about 35 feet, reduced by roughly 2.5 feet for each 45° bend and 5 feet for each 90° bend.
- Exception to the length limit: a longer run if the dryer manufacturer's instructions allow it.
- Transition duct: a single length of listed flexible transition duct between the dryer and the wall, often capped at 8 feet, is permitted.
- Concealed runs: transition duct generally can't run inside walls, floors, or ceilings.
Local adoption and amendments differ, so check the dryer's installation instructions and your local code authority before you tell a customer what's required.
The fire risk is well documented. NFPA's clothes dryer safety guidance reports that U.S. fire departments respond to an estimated average of roughly 13,800 home fires a year involving clothes dryers or washing machines. NFPA identifies failure to clean as the leading contributing factor. Crushed or restricted venting makes lint buildup worse. For ways to discuss this without scaring people, see how to explain dryer vent fire risk to customers.
Should you clean a crushed dryer vent or refuse the job?
Clean a crushed dryer vent or foil duct only if you can do it without damaging the duct or pushing lint into hidden spaces. Refuse or limit the work when cleaning would be ineffective or unsafe.
Clean-or-refuse decision table
| What you find | Typical decision | Why |
|---|---|---|
| Short foil transition, intact, accessible | Clean with air or vacuum only (no rotary brush); recommend upgrade | A brush can snag and tear foil |
| Foil accordion, intact, long run in wall or attic | Clean only the accessible portion if safe; recommend full replacement | You can't verify or reach the whole run |
| Crushed or kinked, but straightens without damage | Straighten, clean gently, recommend replacement | The kink will likely return |
| Crushed flat, torn, or detached | Refuse cleaning of that section; offer replacement | Cleaning won't restore airflow |
| Gas dryer with severely restricted exhaust | Per manufacturer and local guidance, advise not running it until fixed | Restricted exhaust raises combustion-safety concerns |
Set a written policy
Your insurance, training, and local rules shape where these lines fall, so write your clean-or-refuse policy down and apply it the same way on every job. A written policy keeps you from improvising with a customer watching.
How do you explain dryer duct replacement options to the customer?
Explain dryer duct replacement in three parts: what you found, why it matters, and what the options are. Show the photos on your phone. Customers rarely argue with a picture of their own crushed duct.
Offer two or three choices:
- Option A: Replace now. Swap the bad section for rigid or semi-rigid metal duct during this visit.
- Option B: Clean what's safe, replace later. Clean the reachable portion, note the limit in writing, and schedule the replacement.
- Option C: Decline the upgrade. Document the refusal, and clean only if it's safe to do so.
Keep the tone matter-of-fact. "This is the part that's holding your dryer back, and here's what I'd do" lands better than a pitch. For more on raising repairs without losing the sale, see how to upsell a dryer vent reroute or repair.
Sending the options as a written estimate lets the customer approve from their phone. Quotes with one-tap approval turn a doorstep conversation into a signed yes without a callback.
What should you charge to replace crushed or foil accordion venting?
Replacing crushed or foil accordion venting typically runs about $75–$200 for a short transition duct swap. Rigid metal duct installed in a longer run usually costs roughly $10–$30 per linear foot, depending on access. Prices vary by region, with metro and coastal markets running higher than much of the Midwest and many rural areas. They also shift with the cost of sheet metal, fuel, and parts.
What moves the price up or down
- Access: a straight run behind the dryer is quick. A run through a finished wall or crawlspace is not.
- Length and bends: more elbows mean more parts and more labor.
- Termination: a damaged or screened vent cap may need replacing too. See roof vs. wall termination considerations.
- Bundling with a cleaning: the trip charge is already covered when both happen in one visit.
Quoting and scope limits
For the base cleaning price, this dryer vent pricing framework helps you build consistent quotes. Give customers a written local quote rather than a figure from memory. In many states, modifying ductwork through walls or roofs can trigger permit or licensing requirements. Verify what applies where you work, and refer out anything beyond your skill, license, or insurance.
How do you write up a refusal or limited-service note for dryer venting?
A refusal or limited-service note for dryer venting should be short and factual, never accusatory. The customer should sign it or acknowledge it digitally. It needs to state what you found, what you did or didn't do, and why.
Include:
- Date, address, and a one-line description of the duct condition
- What you cleaned and what you left alone
- Your recommendation, such as replacing with metal duct, who should do it, and by when
- A line confirming the customer was shown the photos
Declination wording carries liability weight. Ask your insurer or a local attorney to review your standard template once. If a customer pushes you to "just clean it anyway" and you believe it's unsafe, decline politely: "I'd rather not charge you for a cleaning that won't fix the airflow." Many of those customers call back for the replacement.
How do you turn a bad-duct discovery into repeat business?
A customer who declined dryer duct replacement is a warm lead in 30 to 60 days. Log the finding, set a reminder, then send a short message with the original photo and an offer to schedule the swap. For a system that brings these customers back, see how to build a dryer vent cleaning reminder system.
Frequently asked questions
Is foil accordion dryer duct against code?
Foil accordion dryer duct is often not allowed for the main exhaust run. Many jurisdictions follow the IRC approach: smooth-walled metal duct for the run, with only a short listed transition duct allowed. Check local code and the dryer manufacturer's instructions.
Can you clean foil accordion dryer duct with a rotary brush?
Generally no. A spinning rotary brush can snag and tear thin foil accordion duct. Air-driven or vacuum methods are gentler, and replacement with metal duct is the better long-term fix.
Should you refuse to clean a crushed dryer vent?
If a crushed dryer vent is flattened, torn, or detached, cleaning won't restore airflow. Decline that section in writing, show the customer the photos, and offer replacement.
How much does dryer duct replacement typically cost?
Dryer duct replacement typically runs about $75–$200 for a short transition swap and $10–$30 per linear foot for rigid metal duct. Prices vary by region, access, and material costs, so always quote locally.
How do you protect yourself when you find non-code dryer venting?
Photograph non-code dryer venting before touching it and write a short note on its condition and your recommendation. Get the customer's acknowledgment of any declined repair, and have your insurer or attorney review your template wording.
Ready to get organized?
DoorstepHQ gives you everything you need to run your service business — quotes, invoicing, scheduling, and payments. Completely free.
Get started freeMore from Dryer Vent Cleaning
How to Build a Dryer Vent Cleaning Reminder System That Turns One-Time Jobs into Recurring Customers
A step-by-step system for capturing customer data at the first job and automating annual reminders so dryer vent cleanings rebook themselves.
8 min read
How to Explain Dryer Vent Fire Risk to Customers (Without Scaring Them Off)
A practical script and framework for talking about clogged dryer vent fire risk with customers—honest, specific, and never pushy.
7 min read
The Right Rotary Brush Kit for Dryer Vent Cleaning: How to Choose Your First Setup
What to look for in a dryer vent cleaning brush kit you'll actually run daily — rod types, brush diameters, drill vs. hand-crank, and realistic price ranges.
8 min read